Open Access
Issue |
EPJ Nuclear Sci. Technol.
Volume 2, 2016
|
|
---|---|---|
Article Number | 7 | |
Number of page(s) | 8 | |
DOI | https://doi.org/10.1051/epjn/e2016-50008-7 | |
Published online | 23 February 2016 |
- Y. de Carlan, J.-L. Béchade, P. Dubuisson et al., CEA development of new ferritic ODS alloys for nuclear application, J. Nucl. Mater. 386-388 , 430 (2009) [CrossRef] [Google Scholar]
- P. Dubuisson, Y. de Carlan, V. Garat, M. Blat, ODS Ferritic/martensitic alloys for Sodium Fast Reactor fuel pin cladding, J. Nucl. Mater. 428 , 6 (2012) [CrossRef] [Google Scholar]
- J.S. Benjamin, Dispersion strengthened superalloys by mechanical alloying, Metall. Trans. 1 , 2943 (1970) [Google Scholar]
- L. Toualbi, C. Cayron, P. Olier, R. Loge, Y. de Carlan, Relationships between mechanical behavior and microstructural evolutions in Fe 9Cr–ODS during the fabrication route of SFR cladding tubes, J. Nucl. Mater. 42 , 410 (2013) [CrossRef] [Google Scholar]
- L. Toualbi, C. Cayron, P. Olier et al., Assessment of a new fabrication route for Fe–9Cr–1W ODS cladding tubes, J. Nucl. Mater. 428 , 47 (2012) [CrossRef] [Google Scholar]
- H.R.Z. Sandim, R.A. Renzetti, A.F. Padilha, D. Raabe, M. Klimenkov, R. Lindau, A. Moslang, Annealing behavior of ferritic-martensitic 9%Cr-ODS-Eurofer steel, Mater. Sci. Eng. A 527 , 3602 (2010) [CrossRef] [Google Scholar]
- P. Moayeart, Investigation of the martensitic transformation using dilatometry, CEA Report, DEN/DANS/DMN/SRMA/LA2M, 2013 [Google Scholar]
- A. Ayad, N. Allain-Bonasso, N. Rouag, F. Wagner, Grain Orientation Spread values in IF steels after plastic deformation and recrystallization, Mater. Sci. Forum 702-703 , 269 (2012) [CrossRef] [Google Scholar]
- M. Praud, F. Mompiou, J. Malaplate, D. Caillard, J. Garnier, A. Steckmeyer, B. Fournier, Study of the deformation mechanism in Fe-14% Cr ODS alloys, J. Nucl. Mater. 428 , 90 (2012) [CrossRef] [Google Scholar]
- M. Klimiankou, R. Lindau, A. Möslang, Direct correlation between morphology of (Fe, Cr)23C6 precipitates and impact behavior on ODS steels, J. Nucl. Mater. 367-370 , 173 (2007) [CrossRef] [Google Scholar]
- S. Noh, B.-K. Choi, C.-H. Han, S.H. Kang, J. Jang, Y.-H. Jeong, T.K. Kim, Effects of heat treatments on microstructures and mechanical properties of dual phase ODS steels for high temperature strength, Nucl. Eng. Technol. 45 , 821 (2013) [CrossRef] [Google Scholar]
- S. Ukai, S. Ohtsuka, T. Kaito, H. Sakasegawa, N. Chikata, S. Hayashi, S. Ohnuki, High-temperature strength characterization of advanced 9Cr-ODS ferritic steels, Mat. Sci. Eng. A Struct. 510-511 , 115 (2009) [CrossRef] [Google Scholar]
- R. Miyata, S. Ukai, X. Wu, N. Oono, S. Hayashi, S. Ohtsuka, T. Kaito, Strength correlation with residual ferrite fraction in 9Cr-ODS ferritic steel, J. Nucl. Mater. 442 , S138 (2013) [CrossRef] [Google Scholar]
- M. Yamamoto, S. Ukai, S. Hayashi, T. Kaito, S. Ohtsuka, Formation of residual ferrite in 9Cr-ODS ferritic steels, Mat. Sci. Eng. A 527 , 4418 (2010) [CrossRef] [Google Scholar]
- S. Vincent, J. Ribis, Microstructural and mechanical characterization of CEA ODS steels, Technical report, DEN/DANS/DMN/SRMA/LC2M&LA2M/NT/2013/3393/A, 2013 [Google Scholar]
- C. Cayron, A. Montani, D. Venet, N. Herve, Y. de Carlan, Microstructural characterization of ODS steels after manufacturing and after creep loading, Technical report DEHT/DL/2013/122, 2013 [Google Scholar]
- H. Bakker, H.P. Bonzel, C.M. Bruff, “LANDOLT-BÖRNSTEIN”, Group III: Crystal and solid State Physics, Volume 26, Diffusion in Solid Metals and Alloys (Springer-Verlag, 1990), p. 481 [Google Scholar]
- C.Y. Kung, J.J. Rayment, An examination of the validity of existing empirical formulae for the calculation of Ms temperature, Met. Trans. A 13A , 328 (1982) [CrossRef] [Google Scholar]
- J.L. Béchade, L. Toualbi, S. Bosonnet, Macroscopic and microscopic determination of residual stresses in thin Oxides Dispersion Strengthened steel tubes, Mater. Sci. Forum 768-769 , 296 (2014) [CrossRef] [Google Scholar]
- L. Toualbi, Improvement of the manufacturing route of ODS steels cladding tubes, translated from “Optimisation de la gamme de fabrication de tubes en aciers renforcés par dispersion nanométriques d’oxydes (ODS)”, PhD thesis, CEMEF-Mines ParisTech, 2012 [Google Scholar]
Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.
Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.
Initial download of the metrics may take a while.